BNBM Yuwang waterproof coating series products can be divided into polymer waterproof coating, polymer modified asphalt waterproof coating and polymer cement waterproof coating.
WATERPROOF COATING SERIES
Inorganic waterproof and leakage-preventing material
Waterproof coating ranges
★ Product Description download
The products are classified into retarded type (type I) and quick-setting type (type II) according to the setting time and the usage. Retarded type (type I) is mainly used for waterproofing on wet substrate.
Quick-setting type (type II) is mainly used for waterproofing on substrate with leakage or water inrush.
Product Specifications:
————
This product is a kind of leakage-preventing material with high efficiency, moistureproof, impermeable performance; it is a rigid inorganic waterproof material made of high-quality cement and scientifically mixed with polymers and other additives. It can be moistureproof, impermeable and leak-proof, and can be bonded with a variety of materials. The material can be divided into the retarded type and quick-setting type, both of the two types are one component gray powder.
Product
Introduction
FEATURES
PRODUCT
●substrate treatment: the seepage surface should be firm, clean, smooth and free from looseness. The old surface must be cleaned until the new surface is exposed.
● material preparing: preparing the material according to the proportion of powder: water = 1:0.3-0.4(weight ratio) , and use electric mixer to stir evenly without caking.
● leakage repairing: use the trowel or scraper to coat the substrate strongly for several times. For severe leakage, mix with dry powder and compact or use drainage decompression method, blocking the upper leakage first, then the lower leakage, finally the drainage hole.
● moisturizing maintenance: after half an hour of constructing the leakage repairing material, spraying water to maintain the coating for more than 3 times, covering with plastic cloth or wet materials.
Construction of quick setting material for substrate with water leakage
For repairing of substrate with seepage or water inrush, we should choose quick setting type.
●substrate treatment: use a steel chisel or impact drill to make the leaking place (point) with a certain depth to form a inverted V groove, and clean up the loose debris inside the groove.
●material preparing: preparing the material according to the proportion of powder: water = 1:0.25-0.3(weight ratio) , and use electric mixer to stir evenly without caking.
●leakage repairing: knead the material thoroughly into the shape slightly smaller than the leak and stuff into the leak, squeeze with a wooden stick and hit lightly to make it compactly connected with the surrounding, thus sealing up the leakage. In order to make the sealing effect better, two-times sealing can be taken (the first time sealing 50% of the leak, and the second time sealing all).
●capping: after sealing without leakage, mixing the material with proportion of powder: water = 1:0.3 ~0.4. troweling the leak and its surrounding (10 cm) surface.
Construction of quick-setting type
For repairing of substrate without seepage , we should choose retarded type.
●substrate treatment: the substrate must be fully wet to saturation (no ponding), and it should be firm, clean, smooth (for uneven places, use cement mortar or leakage preventing materials for level finding).
●Material preparing: preparing the material according to the proportion of powder: water =1: 0.3-0.4 (weight ratio) , and use electric mixer to stir evenly without caking.
●constructing: use spatula or scraper to coat the first layer, and spray the coating wet (no water accumulated) after the coating is hardened (no fingerprint left by hand pressure); Then proceed the second layer coating, at the second construction, pressing the layer several times to make it compact.
●reference amount: one layer consumption: 1~1.5kg/㎡; total consumption: 2~3kg/㎡.
Construction of retarded type
METHOD
CONSTRUCTION
no cracking, peeling, falling off
freeze-thaw cycles(20 times)
no cracking, peeling, falling off
heat-resistance(100℃,5h)
retarded type≥0.6
quick-setting type≥0.6
bonding strength/MPa(7d)
retarded type≥1.5
quick-setting type≥1.5
impermeable pressure of specimen/MPa(7d)
1h:retarded type--- quick-setting type≥15.0
3d:retarded type≥3.0 quick-setting type≥4.0
Breaking strength/MPa
1h:retarded type---
quick-setting type≥4.5
3d:retarded type≥13.0
quick-setting type≥15.0
Tensile strength (without treatment) /MPa
initial set:retarded type≥10
quick-setting type≤5
final set:retarded type≤360
quick-setting type≤10
setting time/min
Physical Index
GB23440-2009《Inorganic waterproof and leakage-preventing materials》
STANDARD
EXECUTIVE
retarded type≥0.4
quick-setting type---
impermeable pressure of coating/MPa(7d)
Suitable for roofing, basement, tunnel, culvert, pool and other projects of waterproofing and leakage-preventing.
FIELD
APPLICATION
From Monday to Saturday at 8:00am -18:00pm
Email :wugang@bnbm.com.cn
Address: South of Xingyou Street, West of Jinger Road, Xinglongtai District, Panjin City, Liaoning Province, China
400-600-0427
Contact us
Hydro power
Municipal building
Commercial building
Civil building
Bridge, tunnels and roads
Overseas engineering
Rail roads and subways
Major projects
Classical engineering cases
Waterproof coating ranges
Excellent and Secure Waterproofing System Ranges
Polymer ranges of waterproof materials
Self adhering ranges of modified asphalt waterproof membrane
Hot-torched ranges of modified asphalt waterproof membrane
Products center
Development history
Honor
Enterprise culture
Production bases
Company introduction
Enter BNBM Yuwang